FeatureBoardby Lewis Valentine

NativeCAD for Energy and Power Generation: Turbines, Heat Exchangers and Hydrogen Hardware

Power equipment is rotating machinery, heat transfer and combustion in one package. NativeCAD lets an AI assistant model the plant, size the exchanger and check the blade, with the solvers built in.

Energy hardware is designed by small expert teams against long lists of requirements: duty, pressure drop, blade life, emissions, footprint. Much of the schedule goes to redrawing and re-running as those requirements move. NativeCAD is CAD, FEA and CFD software driven by your AI assistant. It builds the geometry as exact solids, runs thermal, structural and flow checks on it, and reports each result against its requirement.

A turbogenerator on its skid with intake, turbine casing and exhaust
The turbogenerator, modelled as one assembly.

What energy teams do with NativeCAD

  • Lay out whole packages: a turbogenerator from the pad to the exhaust stack.
  • Size heat exchangers and check duty, pressure drop and leak paths.
  • Design hydrogen and fuel-cell hardware from a text brief.
  • Simulate combustion and start-up with flow and chemistry coupled.
  • Qualify rotating blades: modes, Campbell diagram, forced response.

A containerised turbogenerator as one assembly

The turbogenerator is a containerised 42 MW-class natural-gas unit modelled as one B-rep assembly, from the concrete pad to the exhaust stack, with every part mounted to the one it rests on. It is exported once and shown as three detail levels with an engine close-up, an exploded view, group isolation, a section plane and a running clip. For a packager, that is the proposal model, the layout review and the maintenance illustration from one source.

Heat exchangers that meet their duty

The printed gyroid heat exchanger removes 515 W against 482 W required, a 6.9 % margin, at 2.7 kPa air-side pressure drop inside a 5.0 kPa budget, with 0 leak paths between the air and coolant networks. The whole exchanger is 696 g in AlSi10Mg. Duty, pressure drop and separation of the two fluids are checked on the geometry that will be built.

10.3 kW
removed by a one-piece precooler
6.9 %
duty margin on the gyroid exchanger
0
leak paths between fluids

Hydrogen fuel-cell hardware from a brief

The hydrogen fuel-cell precooler was generated from a text brief and prints as one piece. It removes 10.3 kW at 109 g/s of air and 2.5 bar, through 267 tubes with 89.1 m of Ø3.0 mm tube, in 4.06 kg of AlSi10Mg. It is checked for thermal performance, structure, vibration and printability. For teams building balance-of-plant hardware, that is a first article in days.

Two tall cylindrical heat exchanger bodies with end fittings
The one-piece hydrogen fuel-cell precooler.

Combustion and start-up in one loop

Simulation coupling runs a small gas turbine with SU2 compressible CFD, Cantera combustion chemistry and a simulated start-up in one loop. It reaches exit Mach 0.868 and 298.1 N of thrust against a 300 N target. The method is the point: flow, chemistry and the transient solved together on geometry the same assistant can change.

Rotating blades: four constraints and a qualification report

The HP turbine blade is checked by four solvers at once: castability, rim load, tip clearance and aero, at 11,000 rpm. The NASA Rotor 67 qualification solves prestressed modes, a Campbell diagram, forced response and Goodman safety factor, and reports a minimum safety factor of 1.19 against the required 1.5. The variable stator vane stage drives three vane rows from two actuators with fits measured to ISO 286.

A high-pressure turbine blade standing on its root platform
The HP turbine blade checked by four solvers.

What to ask your assistant

Size a plate-fin exchanger for 5 kW with air at 80 g/s and stay under 3 kPa.
    Check that the two fluid circuits never connect.
    Run prestressed modal analysis on this blade at 9,000 rpm and draw the Campbell diagram.
    Section the package at the turbine centreline and export a drawing.

Related reading: aerospace and turbomachinery, simulation teams and metal additive manufacturing.

Questions energy engineers ask

Can NativeCAD design and check a heat exchanger?

Yes. NativeCAD generates exchanger geometry, including printed gyroid cores, and checks heat duty, pressure drop and leak paths between the two fluids. The public gyroid exchanger removes 515 W against 482 W required.

Does NativeCAD simulate combustion?

Yes. The coupled simulation demo runs SU2 compressible CFD with Cantera combustion chemistry and a simulated start-up in one loop.

What does NativeCAD cost?

A NativeCAD MCP / Modeler seat is $200 per seat per year, or $20 per seat per month, with no metered usage. The evaluation needs no key and no sign-up; export, save and import need a seat key. See pricing.

Does my geometry leave my computer?

NativeCAD runs on your own machine: the kernel and solvers run locally and licence validation is fully offline. Files opened in the browser modeler are never uploaded. Your AI assistant sees what you ask it to work on, under your agreement with its provider.

NativeCAD in other industries


NativeCAD is CAD, FEA and CFD software your AI assistant drives over MCP, from Claude, Cursor or your own agent, and in the browser. Every part is an exact B-rep solid that exports as STEP AP242. See what it does, browse every demo, check pricing, or install it.

← Previous Post
NativeCAD for Reverse Engineering and Inspection: Scans, STL Files and Old Drawings Back to Solids
Next Post →
NativeCAD for Jewellery and Consumer Product Designers: Fine Surfaces, Working Mechanisms, Ready to Make