Digital casting

Part in. Printable two-half mould out.

One call turns a part into bolted ceramic mould halves, a funnel, a charge in medallions and a build plate. Three parts, start to finish, below.

1.3 minaverage, part to finished mould set
up to 47%less ceramic than a block mould
up to 13moulds on one build plate, placed and clearance-checked
3 of 3came out as two closed, printable halves
1. Read the partSTEP in, closed solid checked.
2. Find the partingPull direction, draft, undercuts, upright stance.
3. Build the mouldConformal shell, flange, bolts, keys, vents, cores, gate and funnel.
4. Check and shipFreezing check, casting rules, build plate, STL / 3MF / STEP.

01 · Thin-wall cover

Pump cover

Stepped, domed cover with a bolt circle. A flat parting and one closed cavity.

Fully automatedPrintable, review items
19 spart to mould set
47.1%less ceramic than a block mould
1,231 gA356 charge, 109 medallions
2moulds on one build plate

Drag to orbit, pinch or scroll to zoom.

The mould

Two bolted halves, 6 clamp bolts, 2 registration keys, 1 vent, a horizontal parting, so it stands on half A with the gate on top. Wall 6.2 mm on average, 6.0 mm at the thinnest.

Partingplane at z -0.18 mm

Ceramic389 cm³ vs 735 cm³ as a block

Half massesA 315 g, B 449 g

Gating and charge

One gate from the reservoir, sized for 109 medallions. The funnel prints as its own part on the FS-40 spigot.

Charge1,231 g

Yield40.9%

Gate bore26 mm

Funnel127.4 mm tall, 136.9 mm wide

Freezing check

The fast solidification check marks 1 spot to look at before the first pour. The map shows it.

  • Spot 1 at (13, -29, 12) mm. 29,726 mm³ of metal, 1,784 mm³ of predicted shrink.

Last metal to freeze103 s

Build plate

2 moulds with funnel placed in one 305 mm build, minimum clearance, checked on the triangles. One 3MF, ready to send.

Packing18% of the build volume

Build height170 mm

Design for casting checks

  • shrink allowancepass
  • mould envelopepass
  • depowder accesspass
  • alloy windowpass
  • min wallpass
  • min cored holepass
  • draftpass
  • hot spotspass

Automation: nothing left to model

Two closed mould halves, no hand-finishing; 1 item(s) for an engineer to review (solidification).

Work for a designer 0

Nothing here.

For an engineer to review 1

  • solidification review the hot spots: add a riser/chill or thin the wall there (variable wall), then re-run

Download

Mould set (both halves, closed)3MF 200 KBAP214.STEP 127 KB
Build plate (moulds placed)3MF 490 KB

02 · Bracket / arm

Bored arm

Long arm with a 24 mm and a 16 mm bore. Six clamp bolts.

Partly automatedPrintable, review items
80 spart to mould set
15.1%less ceramic than a block mould
628 gA356 charge, 56 medallions
13moulds on one build plate

Drag to orbit, pinch or scroll to zoom.

The mould

Two bolted halves, 6 clamp bolts, 2 registration keys, a foot so it stands upright. Wall 6.3 mm on average, 6.0 mm at the thinnest.

Partingplane at z 1.88 mm

Ceramic387 cm³ vs 456 cm³ as a block

Half massesA 251 g, B 526 g

Gating and charge

One gate from the reservoir, sized for 56 medallions. The funnel prints as its own part on the FS-40 spigot.

Charge628 g

Yield54%

Gate bore26 mm

Funnel103.2 mm tall, 110.6 mm wide

Freezing check

The fast solidification check marks 3 spots to look at before the first pour. The map shows them.

  • Spot 1 at (45, -13, 12) mm. 31,434 mm³ of metal, 1,886 mm³ of predicted shrink.
  • Spot 2 at (-20, -2, 19) mm. 938 mm³ of metal, 56 mm³ of predicted shrink.
  • Spot 3 at (115, 0, 16) mm. 517 mm³ of metal, 31 mm³ of predicted shrink.

Last metal to freeze82 s

Build plate

13 moulds placed in one 305 mm build, minimum clearance, checked on the triangles. One 3MF, ready to send.

Packing22% of the build volume

Build height275 mm

Design for casting checks

  • shrink allowancepass
  • mould envelopepass
  • depowder accesspass
  • alloy windowpass
  • min wallpass
  • min cored holepass
  • draft4 to review
  • hot spotspass
  • Draft on moulded walls, 1 degree rule: 2 curved faces 24 mm tall: add 1 degree (0.419 mm of taper); 2 flat faces 24 mm tall: add 1 degree (0.419 mm of taper).
  • Review note: 4 hole wall faces (24 and 16 mm holes) at 0 degrees. A printed core forms them or they are bored after casting, so they need no draft.

Automation: nearly there

Two closed halves; moldability left for a person to finish by hand; 1 review item(s).

Work for a designer 1

  • moldability open 4.7 mm2 of cavity to the split or add a clean-out

For an engineer to review 1

  • solidification review the hot spots: add a riser/chill or thin the wall there (variable wall), then re-run

Download

Mould set (both halves, closed)3MF 302 KBAP214.STEP 247 KB
Build plate (moulds placed)3MF 3.8 MB

03 · Housing with cored passages

Cored manifold

Housing with internal passages that need printed cores.

Partly automatedPrintable, review items
2.4 minpart to mould set
569 cm³of ceramic for the whole mould
1,748 gA356 charge, 154 medallions
1moulds on one build plate

Drag to orbit, pinch or scroll to zoom.

The mould

Two bolted halves, 4 clamp bolts, 2 registration keys, 1 vent, a foot so it stands upright. Wall 6.1 mm on average, 6.0 mm at the thinnest. 1 printed core, 1 seat cut.

Partingplane at z 100.48 mm

Ceramic569 cm³ vs 581 cm³ as a block

Half massesA 776 g, B 291 g

Gating and charge

One gate from the reservoir, sized for 154 medallions. The funnel prints as its own part on the FS-40 spigot.

Charge1,748 g

Yield53.5%

Gate bore26 mm

Funnel142.2 mm tall, 153.1 mm wide

Freezing check

No isolated pockets. The heaviest section freezes last, outside the feeder, so a riser or chill goes there. The map shows where.

Last metal to freeze229 s

Build plate

1 mould with funnel placed in one 305 mm build, minimum clearance, checked on the triangles. One 3MF, ready to send.

Packing15% of the build volume

Build height142 mm

Design for casting checks

  • shrink allowancepass
  • mould envelopepass
  • depowder access6 to review
  • alloy windowpass
  • min wallpass
  • min cored holepass
  • draft4 to review
  • hot spotspass
  • 4 faces: depowder access.
  • Draft on moulded walls, 1 degree rule: 4 flat faces 120 mm tall: add 1 degree (2.095 mm of taper).
  • Review note: 8 hole wall faces (14 and 8 mm holes) at 0 degrees. A printed core forms them or they are bored after casting, so they need no draft.

Automation: nearly there

Two closed halves; moldability, split left for a person to finish by hand; 1 review item(s).

Work for a designer 3

  • moldability resolve 1571.5 mm2 of undercut (core, extra split piece or redesign)
  • moldability open 1223.2 mm2 of cavity to the split or add a clean-out
  • split review the parting: the part's parting line is freeform, a planar split at z=100.48 was used

For an engineer to review 1

  • solidification review the hot spots: add a riser/chill or thin the wall there (variable wall), then re-run

Download

Mould set (both halves, closed)3MF 326 KBAP214.STEP 293 KB
Build plate (moulds placed)3MF 280 KB

More demos

All demos →

Build your own part with NativeCAD

Try it free with the keyless evaluation · $200 per seat per year · Kernel SDK for products.